How to replace tub drain

How to replace tub drain

If your bathtub drain has become clogged, it means that you will have to replace it. How to replace tub drain is not too difficult of a task, even for the novice plumber. It does require some time and effort.

To get success, you need to know the source of the problem. The source could be a blocked or clogged pipe, a faulty water valve, or some other component in your plumbing system. Once you have determined the source of the problem, it is time to locate the main drain line and drain it.

The location of your main drain line depends on where you live. If you live in an area that gets a lot of snow, chances are good that your main drain line is buried.

How to replace tub drain

Tools Used in replacing tub drain

Tub drains are installed in tubs to provide the water a way out. Many tools available that can be used for replacing a drain, but most people use a heavy-duty wrench or a ratchet with a socket and a pipe wrench.

A common cause of clogged tub drains is hair. Hair, when wet, is a lot like a sponge; it has spaces that can fill with water, and once it’s full of water its weight will keep it from coming back up the drain.

Tools that can be used to replace tub drains include:

  • A plunger
  • A snake
  • A plumber’s helper
  • A closet auger
  • Chemical drain cleaner
  • Wire coat hangers
  • Drain cover

How to remove a tub drain?

Here’s what you need to do:

  1. Remove the overflow plate from the tub drain.
  2. Place a plunger over the opening, making sure it covers all open areas in the drain.
  3. Fill up the tub with water.
  4. Position yourself right over the drain and push down on the plunger to create suction and remove debris that is clogging the drain.
  5. Repeat steps 3 and 4

When you remove the drain from your tub, take the time to clean it thoroughly. If it has a crack or hole, replace it. Turn the water off and use a sponge to wipe away any residue that may be on the drain. Then, use an old towel to dry off the outside of the drain trap. Once it is clean, screw it back into place and turn the water back on.

Clean the Seats Area and Put on New Plumbers Putty

Putty is a type of glue that is used to seal and join two pieces of metal so they form a watertight, airtight, or gas-tight bond. It is also sometimes called lead.

It can be applied to pipe joints, window frames, and door frames. The putty is then smoothed with a trowel, knife, or similar tool and allowed to dry until it becomes hard.

Tub drains are made of two parts: the drain itself and the tailpiece. The tailpiece usually attaches to the bottom surface of the tub, beneath the tub’s rim, and extends downward and outward from the tub.

The drain is a device with a threaded end that attaches to the tailpiece, with threads that match those on the tailpiece.

The threaded end of the drain is attached to the bottom of the tub’s rim with nuts and washers, which also prevent water from leaking between the drain and the tub’s surface.

Insert the New Drain

The new drain is a great invention. It solves the problem of clogged drains by redirecting the flow to a less-clogged section. To install, simply detach the old drain and replace it with the new one.

To install a new drain, you will first need to detach the old one. After detaching the old drain, attach the new one in its place.

A few steps to take before you install the new drain are…

  • First, remove the old drain. Once you’ve done that, apply a bead of silicone sealant to the edge of the drain to make sure it won’t leak.
  • Next, place the new drain in position and attach it to the trap arm with a new washer.
  • Finish by attaching the trap arm to the floor or pedestal pipe.

The new drain should be tight against the wall and flush with the floor so water will flow freely into it. Fill up a bucket with water and turn on the faucet, then check the drain to make sure it is draining properly.

Replacing the tub drain is an easy DIY project for anyone!

It’s a common misconception that replacing a bathtub drain is a difficult project. It’s actually an easy one for anyone who is willing to put in the time and effort to do it.

With the proper tools, it should take less than 30 minutes to install a new bath drain. You’ll need some basic knowledge about plumbing skills, but otherwise, it’s simple as pie.

A bathtub drain is typically made from metal and plastic. The metal piece of the bathtub drain has two holes on each side with threads off the inside of each hole.

Many people are afraid to do DIY projects. It’s not because they’re no good at them, it’s because they don’t want to get their hands dirty. There are a lot of projects that you can do on the cheap using just a screwdriver, but the easiest project for anyone is replacing a tub drain.

It’s just like putting in a kitchen sink drain. The only thing that’s different is that you have to put more muscle into it because there is more weight on it.

How to install a tub drain?

You can save yourself a headache by following these instructions from your local plumber.

  1. Turn off the water under the sink. There will be a shut-off valve under the sink, which has a screw-type handle. If not, there may be a shut-off valve in the laundry room or basement.
  2. Unscrew the old drain and remove it from the tub. Place a bucket under the drain to collect any water that drains out. Lift up on the new drain and insert it into the hole. Screw it in place.
  3. Check for leaks after turning on the water.

Conclusion: How to replace tub drain

As you can see, replacing a tub drain is not as difficult as it may seem. If you are looking for a way to save money and do the job yourself, you’re in luck! Just follow these steps and save yourself some money!

At this point, you will have all of the information necessary to go ahead with your repair project. Now that you’ve learned how to replace a tub drain, there’s no need to fear plumbing jobs in the future!

Similar Posts

Leave a Reply

Your email address will not be published.